Clutch nut locking pliers     Made of stainless steel Locking vice-grip type Maximum spacing 122mm Total length 29.5cm Adjustable spacing by means of a thumbwheel Allows clutch nut to be locked for tightening and loosening Prevents damage to the nut

Anodized aluminum brake fluid reservoir with adjustable mounting bracket It fits in the place of any reservoir separate from the master cylinder. Depending on the bike, it will be suitable for the front as well as for the rear, and for the clutch when it is a hydraulic system. Caution , this is an...

Pair of universal LED turn signals in aluminum. Number of LED on each indicator : 15 Length (out of screw thread) : 36 mm Width / Diameter : 28 mm Screw diameter : 8 mm Wires length : 440 mm NOTE :  Before ordering, just make sure...

Pair of front footrests, aftermarket model based on the OEM, specific for the following for  many KAWASAKI (see compatibility list below). Caution : these foot-pegs will perfectly, but in some case the provided hardware may not be a perfect match...

Rear-view mirrors block-off plates for many  KAWASAKI  models. You will find the motorcycles compatibility list below.   Distance between the fastening points : 47mm   Sold by pair.

Pair of adhesive grips for the tank sides (right and left traction pads). Specific for KAWASAKI :   Ninja H2 SX / SE 2018 - 2021        Non-slip with a finish similar to sandpaper (type 240 for beginner in car painting).

Automatic tie down strap with ratchet tensioner and its 2 hooks to secure the bike transport.    Measurements and technical information : LENGTH : 18 cm Unwound LENGTH : 1,6 m WIDTH : 2,6 cm FIXATION TYPE : "S" Hooks with rubber protection    Sold by...

Pair of universal  LED  turn signals in aluminum and an orange lighting.  Number of LED on each turn signal : 17 Length (out of screw thread) : 86 mm Width : 38 mm Screw diameter : 8 mm Wires length : 210 mm

Pair of universal  LED  turn signals in aluminum. New model with 1 powerful LED light, orange color.

Pair of anodized aluminum bar end plugs, available in several colors. Universal model with a covering plastic cap.   Fits on all handlebars with an internal diameter of  14mm  or  18mm  (adapters provided). These handlebar caps can also be installed on handlebars with an integrated  6mm  threaded spot (6 mm screw provided)....

Pair of universal  LED  turn signals in aluminum.  E8 E-marked  model, with  an orange light. All the universal turn signals models we propose are visible on the last photo!

Pair of universal  LED  turn signals in plastic with orange lighting and a blinking indicator on the rear of the turn signals, towards the pilot (blinking on both sides).

Pair of universal LED turn signals in aluminum. E8 E-marked model, with 9 LED and an orange light.

Pair of universal  LED  turn signals in plastic.  E8 E-marked  model, with 15 LED and an orange light. Design with a center hole. For installation on MT07 / FZ07, you must install and reverse a  turn signal shutter  so the nut can be screwed on the turn signal's rod. 

Pair of universal rubber and anodised aluminum handlebar grips with an internal diameter of  22 mm  on the left side (clutch) and  24 mm  on the right side (throttle).   Measures : Length: 120 mm Depth: Hollow...

Pair of universal rubber and anodised aluminum handlebar grips with an internal diameter of  22 mm  on the left side (clutch) and  24 mm  on the right side (throttle).   Measures : Length: 120 mm (+ 13 mm with end caps) Depth:...

Pair of universal  LED  turn signals in plastic with 8 LEDs and an orange light.

Secondary LED light, universal model with a mounting bracket designed to fit on all handlebars with an external diameter of 22 or 28 mm. Very good lighting quality, white light color. 3200 Lumens Sold per unit.

Kit of adhesive tapes for the inner rim (front and rear). Model with RACING logo, designed for 17” rims.    Note : Depending on models, you may need to recut some of the tape, more information available below.

Kit of adhesive tapes for the inner rim (front and rear). Model with NINJA logo, designed for 17” rims.   Note  : Depending on models, you may need to recut some of the tape, more information available below.