Anodised universal valve caps, different colors available. Sold by pairs.      Weight :  5g         

Plastic funnel. Sold by unit.       DIMENSIONS :  Length: 290 mm Diameter: 78 mm for the widest (input) / 9.5 mm for the thinnest (output)     

Scratch strap to block your brake lever to secure your bike transport.    Measurements and technical information : LENGTH: 33,5 cm WIDTH: 2,5 cm    Sold by unit, such as shown in the pictures.

Titanium grub screw for the rear brake pad axle. Suitable for the motorcycle models listed below in the description. INFORMATIONS :  Total Length : 5,7 mm Thread Length : 5,7 mm Weight : 1,22 g

High quality brake cleaner spray   High Performance Cleaner 600ml ball valve aerosol: can be used in any position Contains ozone-friendly propellant gas Brake cleaner containing no FCKW, CKW, cadmium, lead or caustic substances

Aluminium bracket original style for brake fluid reservoir mounting. This bracket is similar to the ones found on many sports bikes with a separate master cylinder such as GSXR / CBR / YZF R1 / R6 / ZX6R / ZX10R.     Anodised aluminium for a good finish Easy to replace  8 and 11diameter 29 mm...

Turn-to-Close, Turn-to-Open 1/4 steel Fastener   Available in the following dimensions: 14mm, 17mm, 19mm.     Sold by unit, such as shown in the pictures. Decreasing prices : 3 € each 25 €  for 10 units 45 €  for 20 units

Pair of resistors for LED turn indicators. Sold by pairs. 1 pair of resistors is necessary for 1 pair of LED turn signals (USUALLY enough, although we cannot take responsibility if it is not : on some rare models you may need more than 1 resistor per blinker).  Power : 10W 10 ohm

Relax cruise control throttle grip for right side handlebar grip. Made in plastic, it will easily install directly on your throttle grip and will allow you to relax your wrist during long journeys. Universal model, will fit on nearly all accelerator grips.

Pair of resistors for LED turn indicators.   Sold by pairs. 1 pair of resistors is necessary for 1 pair of LED turn signals (USUALLY enough, although we cannot take responsibility if it is not : on some rare models you may need more than 1 resistor per blinker).   Power :  20 W 10 oHm 20 W 15 oHm

Tie down strap extension.   Measurements and technical information : LENGTH 1 : 50 cm LENGTH 2 (openned) : 1,0 m WIDTH : 2,5 cm   Sold by unit, such as shown in the pictures.

Turn-to-Close, Turn-to-Open 1/4 steel Fastener for allen key.   Available in the following dimensions: 14mm, 17mm.     Sold by unit, such as shown in the pictures. Decreasing prices : 3 € each 25 €  for 10 units 45 €  for 20 units

Frame cap kit universal.     Made of hard plastic Fits into the holes in the frame where the engine mounting screws are located Protects screws and bolts from moisture and corrosion Provides a neater finish Various diameters

Decorative anodised screw with colored offset.   INFO : M6 screw (6mm diameter) Screw length : 24 mm Length of the colour part : 20 mm Diameter of the colour part : 15.5 mm

Turn signals spacers adapters in plastic, specific for many YAMAHA models, produced from 2002 and over.    In case of doubt, your OEM turn signals must be similar to those displayed on pictures 4 and 5.    1 set of 4 spacers adapters is necessary for 1 pair of turn signals (2 adapters per turn indicator)

Motorcycle-design key ring, different models available.

Screw and cage nut in anodised aluminum. Sold per unit. Various colors available.

YAMAHA Keyrings - different models and designs available.

Decorative screw with anodised colored washer. M6x16mm

Windscreen fastening screws in anodised aluminum.   Sold individually (1 screw + washer + threaded rubber).   Caution : diameter 5 mm for this windscreen screw, on some Italian motorcycles you will need a diameter 4. Length : 15mm   Note: The design and head of the screws you will receive can be slightly...